Pressed Male Reducers

$13——29 USD

Pressed Bends is a common connecting pipe used in pipeline installation. It connects two pipes with the same or different nominal diameters to make the pipe turn to a certain Angle. The production efficiency of stamping processing is high, and the operation is convenient, and it is easy to realize mechanization and automation, because stamping is dependent on stamping die and stamping equipment to complete the processing Materials, angles and diameters are customizable. Choose good galvanized...

$12——13 USD

Reducing pipe (size head) is a piece of pipe used in reducing pipe diameter. The forming process is usually used for reducing the diameter pressing, expanding pressing or reducing the diameter and expanding pressing, for some specifications of reducing pipe can also use stamping forming. This Pressed Female Reducers is perfect for heat recovery systems and ventilation system. Standard nominal diameters up to DN 315 mm are available for pressed pieces at a lower price and with an improved...

$13——15 USD

FN reducers are centric and male-male pressed. If gasket is not needed, please specify “X“ after type, i.e. FX. 1, high strength, small resistance, good sealing performance, beautiful appearance, simple installation, long service life; 2, the use of raw materials are made of stainless steel plate; 3, the inner and outer walls are smooth, the air duct resistance is small, the air supply and exhaust do not produce secondary noise, reduce energy consumption, save operating costs; 4, simple...

$6——43 USD

Pressed T-Pieces are made up of pressed collar saddle and main pipe. TP type is made up of two pressed parts. If gasket is not needed, please specify “X” after type, i.e. tx. Pressed T-Pieces are made up of collar saddle and main pipe. TVX type is tilted T-piece. If gasket is needed, please delete “X”after type, i.e. Tv. lf no special instruction, 0°is 45°，and other angles should be specified in advance. TVBX type is made up of TVX type and bend. Standaro d TVBX is without gasket, and if gasket...

$13——29 USD

Ducting Bends for ventilation are produced in diameters range 80 mm to 1600 mm of galvanized, aluminum and stainless steel sheet at 15, 30, 45, 60 and 90 degree angles. It is recommended to choose the version with EPDM seals to ensure achieving "D" class leakage (airtightness) according to EN 12237 (SITAC certificate). In both versions there are 4 types of ducting bends: BP (w/o seals) and BPL (with seals) pressed bends - in diameters range 80 to 250 mm. BS (w/o seals) and BSL (with seals)...

$6——43 USD

Pressed T-Pieces are made up of pressed collar saddle and main pipe. TP type is made up of two pressed parts. If gasket is not needed, please specify “X” after type, i.e. tx. After the pieces are cut, we brake and bend to form the duct fittings and custom sections. TVBX type is made up of TVX type and bend. Standaro d TVBX is without gasket, and if gasket is needed, please delete “X” after type, i.e. TVB. Pressed T-Pieces Ducting Part A tee-shaped connecting segment for your ventilation...

$6——43 USD

How the Pressed T-Pieces Works The Pressed T-Pieces is a simple way to connect two sets of ducting to one outlet point. Manufactured from extremely tough, galvanised steel, these connecting segments are highly robust and durable. The diameter of all 3 of the Duct connections is the same. Pressed T-Pieces are made up of pressed collar saddle and main pipe. TP type is made up of two pressed parts. A Pressed T-Pieces connecting segment for your ventilation system. If gasket is not needed, please...

$13——29 USD

High quality stainless steel, galvanized sheet, features: corrosion and rust, good sealing. Segmented Bends from the production process is divided into: spiral seam forming, welding forming, a total plate forming; Elbow Angle: 45°, 60°, 90° or customized duct elbow. Can be customized for thermal insulation and non thermal insulation. Pressed Bends are designed for building ventilation systems based on plain and spiral duct. Seam welds improve the air tightness of the ventilation system, while...

$13——29 USD

The pressed form of the ventilation piece helps to reduce the flow resistance and the pressure loss. If there are Stainless Steel Duct and HVAC And Ancillary Accessories, please contact our company to make a list. Pressed bends are designed for building ventilation systems based on SPIRAL ducts and plain ducts made from stainless steel sheet. Seam welds provide air tightness class C without the need to use any other sealants. It is connected by insertion into a spiral catheter. Stamping elbow...

$13——29 USD

The production efficiency of stamping processing is high, and the operation is convenient, and it is easy to realize mechanization and automation, because stamping is dependent on stamping die and stamping equipment to complete the processing Materials, angles and diameters are customizable. Pressed Bends is a common connecting pipe used in pipeline installation. It connects two pipes with the same or different nominal diameters to make the pipe turn to a certain Angle. Choose good galvanized...

$13——29 USD

Pressed bends are designed for building ventilation systems based on SPIRAL ducts and plain ducts made from stainless steel sheet. Seam welds provide air tightness class C without the need to use any other sealants. The piece is connected with a duct by inserting one into the other. The pressed form of the ventilation piece helps to reduce the flow resistance and the pressure loss. Stamping elbow is a common connecting pipe used in pipeline installation. It connects two pipes with the same or...

$13——29 USD

Pressed bends are based on spiral ducts and plain ducts made from stainless steel sheet. Seam welds provide air tightness class C without the need to use any other sealants. The piece is connected with a duct by inserting one into the other. The pressed form of the ventilation piece helps to reduce the flow resistance and the pressure loss. Stamping elbow is a common connecting pipe used in pipeline installation. It connects two pipes with the same or different nominal diameters to make the...

$12——13 USD

Suitable for the size and diameter conversion of Spiral Ducts in ventilation system. The largest end of the Pressed Female Reducers fits over a fitting and the smallest fits into a Spiral Ducts. This allows another large fitting of the same diameter to be installed directly onto the Pressed Female Reducers. Reducing pipe (size head) is a piece of pipe used in reducing pipe diameter. The forming process is usually used for reducing the diameter pressing, expanding pressing or reducing the...

$12——13 USD

The larger end is female without a gasket to fit over T-pieces and bends. The small end is male with a double EPDM gasket to slip into spiral ducts. This reducer helps to save installation space, but it increases the flow resistance compared to RSCLFL long reducers. Standard nominal diameters up to DN 315 mm are available for pressed pieces at a lower price and with an improved finish. Reducing pipe (size head) is a piece of pipe used in reducing pipe diameter. The forming process is usually...

$12——13 USD

Suitable for the size and diameter conversion of Spiral Ducts in ventilation system. The largest end of the Pressed Female Reducers fits over a fitting and the smallest fits into a Spiral Ducts. This allows another large fitting of the same diameter to be installed directly onto the Pressed Female Reducers. Reducing pipe (size head) is a piece of pipe used in reducing pipe diameter. The forming process is usually used for reducing the diameter pressing, expanding pressing or reducing the...

$12——13 USD

This Pressed Female Reducers is perfect for heat recovery systems and ventilation system. Standard nominal diameters up to DN 315 mm are available for pressed pieces at a lower price and with an improved finish. Reducing pipe (size head) is a piece of pipe used in reducing pipe diameter. The forming process is usually used for reducing the diameter pressing, expanding pressing or reducing the diameter and expanding pressing, for some specifications of reducing pipe can also use stamping...

$13——15 USD

FN reducers are centric and male-male pressed. If gasket is not needed, please specify “X“ after type, i.e. FX. 1, This product is used in Marine engineering, laboratory engineering and other ventilation pipe fittings connector; 2, the use of raw materials are made of stainless steel plate; 3, the inner and outer walls are smooth, the air duct resistance is small, the air supply and exhaust do not produce secondary noise, reduce energy consumption, save operating costs; 4, can be cut, can be...

$13——15 USD

FN reducers are centric and male-male pressed. If gasket is not needed, please specify “X“ after type, i.e. FX. 1, simple installation, labor saving, time saving, shorten the construction period; 2, the use of raw materials are made of stainless steel plate; 3, the inner and outer walls are smooth, the air duct resistance is small, the air supply and exhaust do not produce secondary noise, reduce energy consumption, save operating costs; 4, high strength, small resistance, good sealing...

$90——200 USD

The inner angles of SBW could be rectangular or circular arc, when ordering please specify. If the defending net is demanded, please indicate. Square duct can be made according to customer requirements, in ine with customer requirements of the size and specifications, shaped tube to provide drawings and detailed instructions. Connection Form: Rectangular duct with a common plate flange and angle flange, cutting flange and other forms of connection. Corner flange made of angle steel flange,...

$13——29 USD

Pressed Bends is a common connecting pipe used in pipeline installation. It connects two pipes with the same or different nominal diameters to make the pipe turn to a certain Angle. The production efficiency of stamping processing is high, and the operation is convenient, and it is easy to realize mechanization and automation, because stamping is dependent on stamping die and stamping equipment to complete the processing Materials, angles and diameters are customizable. Choose good galvanized...